Say exactly what you mean
One team wanted Spider-Man climbing Marina Bay Sands, but nobody named the building. It came back with New York style windows.
Name the place, the size and the style. Anything you leave out gets a guess.
On 17 November 2026, six student teams each took an idea from a sentence to a file ready for a 3D printer, in one morning. Here are the four steps, what each tool is for, and what changed their results.
Claude Code is your personal assistant. Tell it what you want in plain words. It helps you word the request for Meshy, then runs Blender, FreeCAD and OrcaSlicer.
Each step uses one tool and ends in one result you can check. Under each step is a request you can copy: change the words in [brackets].
A first 3D model
Turns a picture or a sentence into a 3D model in minutes.
Skip it and you model the shape by hand, which takes hours.
I want to 3D print [what you want to make]. Before we make anything, ask me about the place, the size in millimetres and the style. Then write the request I should give Meshy.
A closed surface at the right size
Closes holes in the surface, alters the shape, and sets the size and the way up.
Skip it when the check finds nothing to fix and you want no changes. A printer needs one closed surface to tell inside from outside.
Check [my model file] in Blender for 3D printing: holes, surfaces that do not close, the size and which way up it sits. Tell me what you find before you fix anything, and keep the original file unchanged.
Parts in exact millimetres
Adds and alters parts to exact measurements: a flat base, a slot, a hole.
Skip it when nothing on the model needs an exact size.
Make a flat base [60] millimetres wide, [60] millimetres long and [3] millimetres thick in FreeCAD. Join it under my model with whichever tool keeps the surface closed. Save the result as a new file, check that file again for damage to the surface, and tell me the final size.
A print file with a known time
Cuts the model into layers, flags problems and estimates the print time.
You cannot skip it: the printer only reads a sliced file, and only the slicer shows where a print needs supports.
Slice [my model file] in OrcaSlicer for [my printer]. Tell me the print time, the filament it uses and any warnings. If it takes more than [3] hours, suggest what to change, starting with the way up and the supports.
We wrote these requests after the workshop. They are not what the teams typed. We ran each once on a test model. We reworded the third request after its run and ran it once more: the join stayed closed, and the file sliced without warnings.
Each problem belongs to one step. To change the shape, use Blender when you judge the change by eye and FreeCAD when it needs an exact measurement.
The shape is not what you imagined
go back to Meshy
Name the place, the size and the style in your request.
A check finds a hole in the surface
go back to Blender
Close it before you add anything.
You want to change part of the shape
go back to Blender
Alter that part instead of drafting again.
The model tips over, or a part must fit
go back to FreeCAD
Add a base or a part made to an exact size.
You have just joined a part
go back to Blender
Check the surface again. Most joins we tested damaged it.
The print time is too long
go back to OrcaSlicer first
Try a different way up or fewer supports. Then a simpler shape in Meshy, or a smaller size in Blender.
The assistant helped most at repair.
Yes, when the model needs no repair and no exact parts. On 16 November 2026, three of our test models came out of Meshy with no holes and went straight to the slicer.
We tested skipping a step and joining a part on those three models, sliced in Bambu Studio and never printed. A smaller size printing faster is expected, not measured. The rest is from the room, or from what each tool does.
The request changed the shape. Detail changed the print time. The model behind the assistant changed the quality.
One team wanted Spider-Man climbing Marina Bay Sands, but nobody named the building. It came back with New York style windows.
Name the place, the size and the style. Anything you leave out gets a guess.
Intricate patterns were hard to model and slow to print. OrcaSlicer estimated about 20 hours for one team's dragon.
Before you print, ask whether a simpler surface, a smaller size or a different way up would do.
One team used Sonnet 5.5 to save cost and could not get good models. Opus 5.5 handled the work, and Fable 5.2 did best.
One workshop, not a benchmark. Here the cheaper model cost more time than it saved.